隨著社會的快速發展,各行各業都紛紛推出了自己的新產品,而旋轉供料器的問世,很快受到了廣大客戶的一致好評。但是有些朋友可能會發現,耐磨供料器使用一段時間之后會有雜音出現,那么對于這種情況,應該如何進行排除呢。機殼與轉子接,擴大間隙,使之達到恰當?shù)拈g隙。機殼內表面有粉體物附著,粉體物溶化,則側板與轉子間隙消失,縮小轉子端面面積。轉子與側板之間滯留粉體物,從側面絲堵部位進*氣體清洗。為了您的耐磨供料器可以更好的進行工作,一定要記得定期對其進行保養以及清理哦。各注油部位定時注油。鏈條的松緊程度。密封壓蓋有無氣體泄漏現象。各部溫升是否正常。經常檢查旋轉供料器運轉中有無雜音或振動。拆下電機地腳螺栓,將電機與減速機分開。
With the rapid development of society, all walks of life have launched their own new products, and the advent of rotary feeder has soon been highly praised by the majority of customers. However, some friends may find that there will be noise after the wear-resistant feeder is used for a period of time, so how to eliminate this situation. The casing is connected with the rotor to expand the clearance and make it reach the appropriate clearance. There is powder attached to the inner surface of the casing. When the powder dissolves, the gap between the side plate and the rotor disappears and the end face area of the rotor is reduced. Powder remains between the rotor and the side plate, and gas is injected from the side plug for cleaning. In order to make your wear-resistant feeder work better, you must remember to maintain and clean it regularly. Fill oil regularly at each oil filling position. The tightness of the chain. Whether the sealing gland has gas leakage. Whether the temperature rise of each part is normal. Frequently check whether there is noise or vibration during the operation of the rotary feeder. Remove the anchor bolts of the motor and separate the motor from the reducer.
拆下蝸桿座螺栓,將支座取下。用油盆接好,將渦輪室端蓋拆下放油。將渦輪定位螺栓拆下取出渦輪鍵。將兩側墻板螺栓拆下,取出墻板,取出轉子。將墻板軸承取出。將蝸桿從支座上取出,取下軸承。用洗油汽油清洗渦輪、蝸桿、軸承,清洗渦輪室蝸桿支座。石磨面粉機是產粗糧的主要設備,供料器的作用是把物料喂入到輸送管道中,并且在這里物料和空氣得到充分混合,繼而被氣流加速和輸送。所以喂料器是石磨面粉機的咽喉部件,它的結構性能對石磨面粉機的輸送量、工作的穩定性、能耗的高低有很大影響。在選擇石磨面粉機喂料器的時候,應滿足相應的要求,物料通過供料器喂入輸料管時,應能和空氣充分混合。要求物料均勻地分散到氣流中,這樣才能更好地發揮氣流對物料的加速、懸浮和輸送作用,不于掉料。
Remove the bolts of the worm seat and remove the support. Connect it with the oil basin and remove the turbine chamber end cover to drain the oil. Remove the turbine locating bolt and take out the turbine key. Remove the bolts of the wallboard on both sides, take out the wallboard and take out the rotor. Take out the wallboard bearing. Take out the worm from the support and remove the bearing. Clean the turbine, worm and bearing with washing oil and gasoline, and clean the worm support in the turbine chamber. The stone mill flour mill is the main equipment for producing coarse grain. The function of the feeder is to feed the materials into the conveying pipeline, where the materials and air are fully mixed, and then accelerated and transported by the air flow. The structure of flour feeder has a great influence on the stability of flour feeder. When selecting the feeder of stone mill flour machine, it shall meet the corresponding requirements. When the material is fed into the feeding pipe through the feeder, it shall be able to fully mix with the air. The materials are required to be evenly dispersed into the air flow, so as to give better play to the acceleration, suspension and transportation of the air flow to the materials and avoid falling materials.
The above is a detailed introduction about Guangdong rotary feeder. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://lzdbgs.com.cn/